工程案例

MPE(S)系列潛水切割泵絞刀泵MPE(S)系列潛水切割泵絞刀泵的用途社區、市政管網、綜合污水處理廠、大樓地下室汚水處理設備、地鐵工程等，尤其適合介質中含長纖維之廢水。食品、皮革、紙漿、印染、鋼鐵等產品的污水排放。屠宰場所、農村沼氣池的汚水排放。工業用排水、其它用水、其他用途之排水。For sewage removal from &nb

在線預約

產品詳情PRODUCT DETAILS

MPE(S)系列潛水切割泵絞刀泵

MPE(S)系列潛水切割泵絞刀泵的用途

社區、市政管網、綜合污水處理廠、大樓地下室汚水處理設備、地鐵工程等，尤其適合介質中含長纖維之廢水。食品、皮革、紙漿、印染、鋼鐵等產品的污水排放。

屠宰場所、農村沼氣池的汚水排放。

工業用排水、其它用水、其他用途之排水。

For sewage removal from living unit and house in scattered settle ment where the laying of a conventional sewer would be too expensive,or where large ground undulation are present, or where it is only possible to lay pipe lines of small diameter.

For sewage removal from motorway resting sites, communal buildings and for renovation of buildings or parts of a city.

For use in slaughter houses,food processing plant, paper factories, agriculture and similar areas.

泵運行介質/Medium Pumped

Faecal matter and heavily polluted sewage, max. medium temperature： continuous operation =40*C, if unit submerged, shortterm to 60tJ

連續長期運行溫度小于40°C,整機浸沒，短時運行溫度小于60°C。

設計Design

The water pressure-tight encapsulated fully flood-proof motor and the pump section form a compact robust unit construction.

Motor： Three-phase 380-415V or single-phase 220-240V 50Hzor 60Hz, Insulationclass F. protection type IP68,cooled by amply dimensioned cooling areas.

電機：三相鼠籠式電機380-415V,或單相220-240V,頻率為50或60Hz.絶緣等級F級，防護等lP68o

Bearing： The motor shaft is supported in lubricated-for-life maintenance -free ball bearings.

軸承：進口NSK軸承。

Shaft Sealing between motor and hydraulic section and motor side by means of high quality sealing units using two silicon carbide mechanical seals, independent of direction of rotation and resistant to temperature shock.

機械密封：釆用雙道串聯式機械密封。

Discharge/出水口徑：MP75-4OO=DN5O with ISO-flange

MP550-750=DN80 with ISO-flangea

Shredding System consisting of spiral bottom plate with stationary cutter ring with cutting edges and a shredding rotor located before the impeller for optimum blockage-free running.

水泵部件設計先進合理，水泵葉輪前加裝切割旋轉刀頭，進水口部裝固定刃，使被抽吸介質中的雜質在進入葉輪流道之前，被徹底絞碎，無堵塞現象。

TCS— Thermo— Control— System by means of thermal sensor in the stator to give a warning and switch off the motor in the event of excessive temperature occurring.

溫度過熱保護：電機內預置熱敏開關，當溫度大于135°C時，自動斷開，保護電機。

DI—System for Seal Monitoring consisting of an electrode in the oil chamber and optical and/or acoustic inspection indication should leakage at the shaft sealing occur.

泄漏監測：油室內安裝泄漏監測探頭。